| Posted By |
Message |
|
|
How do I reset my CBEFM?
I completely screwed up this month and the month before and I want to start from scratch. If I just try again next month will it remember my previous cycles?
|
Posted 3/17/11 12:27 AM  |
| |
|
Long Island Weddings
Long Island's Largest Bridal Resource |
MrsKS
Thank You St. Gerard.....
Member since 12/09 8306 total posts
Name:
Kerri
|
Re: How do I reset my CBEFM?
oh wow.
what happened? did you skip a test or something?
IDK about resetting them but if you just "start over" next cycle... it's going to probably take some time to get used to you again.
When I skipped a test, it took me about 3 cycles for it to straighten out. It was giving me high days way too early and the peak's I don't think were my actual peak days. It was screwy and wonky for those 3 cycles.. but then it was better and worked perfectly.
There MIGHT be a reset button.... IDK why but I vaguely remember a reset button, but I never used it so IDK much about it. Or if it even exists.
You could also try to call the pros... call that 800 number in the booklet; they should have more information for you.
|
| Posted 3/17/11 2:00 AM |
| |
|
emilylives
biking
Member since 12/09 2163 total posts
Name:
Emily
|
Re: How do I reset my CBEFM?
To reprogram the monitor:
1) Ensure monitor is switched off.
2) Insert a Test Stick into the Test Stick slot, checking the position carefully, as there will be no symbol to tell you that the Test Stick is correctly inserted.
3) Press and hold the m button while you complete steps 4, 5, and 6.
4)Press the On/Off Button to turn your Monitor on.
5) The "insert test stick" symbol will be displayed. Continue to hold the m Button and leave the Test Stick in position.
6) After approximately 15 seconds, all symbols on the Display Screen will be shown. The "insert test stick" symbol will again be displayed. The m Button can now be released and the Test Stick removed.
7) You should see the following symbols on your Display Screen '--m'. Your Monitor is now reprogrammed and ready for use.
(These are instructions from page 28 of the Instruction Booklet.)
|
| Posted 3/17/11 6:22 AM |
| |
|
|
|
Re: How do I reset my CBEFM?
Posted by MrsKS
oh wow.
what happened? did you skip a test or something?
Well the first time I used it I had a miscarriage and when I turned it back on when I finally got my period it was on day 60. Then this month I was so excited when I got my period that I set it late in the day and then it just got all screwed up with daylight savings time. It wouldn't ask for a new test until 9 and I have to leave for work before then.
|
| Posted 3/17/11 8:53 PM |
| |
|
|
|
Re: How do I reset my CBEFM?
Posted by emilylives
To reprogram the monitor:
1) Ensure monitor is switched off.
2) Insert a Test Stick into the Test Stick slot, checking the position carefully, as there will be no symbol to tell you that the Test Stick is correctly inserted.
3) Press and hold the m button while you complete steps 4, 5, and 6.
4)Press the On/Off Button to turn your Monitor on.
5) The "insert test stick" symbol will be displayed. Continue to hold the m Button and leave the Test Stick in position.
6) After approximately 15 seconds, all symbols on the Display Screen will be shown. The "insert test stick" symbol will again be displayed. The m Button can now be released and the Test Stick removed.
7) You should see the following symbols on your Display Screen '--m'. Your Monitor is now reprogrammed and ready for use.
(These are instructions from page 28 of the Instruction Booklet.)
Thank you for posting the instructions! I should have thought to check the manual but it's been a long week.
|
| Posted 3/17/11 8:54 PM |
| |
|
emilylives
biking
Member since 12/09 2163 total posts
Name:
Emily
|
Re: How do I reset my CBEFM?
Posted by InTheTTCcloset
Posted by emilylives
To reprogram the monitor:
1) Ensure monitor is switched off.
2) Insert a Test Stick into the Test Stick slot, checking the position carefully, as there will be no symbol to tell you that the Test Stick is correctly inserted.
3) Press and hold the m button while you complete steps 4, 5, and 6.
4)Press the On/Off Button to turn your Monitor on.
5) The "insert test stick" symbol will be displayed. Continue to hold the m Button and leave the Test Stick in position.
6) After approximately 15 seconds, all symbols on the Display Screen will be shown. The "insert test stick" symbol will again be displayed. The m Button can now be released and the Test Stick removed.
7) You should see the following symbols on your Display Screen '--m'. Your Monitor is now reprogrammed and ready for use.
(These are instructions from page 28 of the Instruction Booklet.)
Thank you for posting the instructions! I should have thought to check the manual but it's been a long week.
Totally understand!! :) It's a miracle I even still have the manual.
|
| Posted 3/18/11 12:14 AM |
| |
|
